HDI Low Viscosity Covesro XP2860
Date：2023-11-15 Categories：Brand Product
Characterization :
Aliphatic polyisocyanate based on hexamethylene diisocyanate.
As the hardener component for lightfast, weather-stable coating systems.
Form supplied:100 %
Characteristic data*:
Property
|
Value
|
Unit of measurement
|
Method
|
NCO content
|
approx. 20.0
|
%
|
M105-ISO 11909
|
Viscosity at 23 °C
|
approx. 500
|
mPa·s
|
M014-ISO 3219/A.3
|
Color value (Hazen)
|
≤ 80
|
|
M017-EN 1557
|
Monomeric HDI
|
≤ 0.16
|
%
|
M106-ISO 10283
|
*These values are provisional. Binding supply specifications will not be available until the final product data sheet is published.
Other data**:
Property
|
Value
|
Unit of measurement
|
Method
|
Viscosity at 25 °C
|
approx. 450
|
mPa·s
|
DIN EN ISO 3219/A.3
|
Equivalent weight
|
approx. 215
|
|
|
Flash point
|
193
|
°C
|
DIN EN 22 719
|
Density at 20 °C
|
1.106
|
g/cm3
|
DIN EN ISO 2811
|
**These values provide general information.
Solubility / thinnability :
The product is compatible with the following solvents: ethyl acetate,butyl acetate, 1-methoxypropylacetate-2, acetone, methyl ethyl ketone, methyl isobutyl ketone, cyclohexanone, toluene, xylene, solvent naphtha® 100 and mixtures thereof.
Aliphatic hydrocarbons are unsuitable as solvents.
Desmodur® XP 2860 should not be thinned to below a solids content of 40 % by weight. Prolonged storage of a solution with lowerbindercontent may result in turbidity and sedimentation. Storage stability of the thinned product should be tested in each case.
Compatibility :
Desmodur® XP 2860 can be blended with most Desmodur® grades,such as: Desmodur® N 75, N 100, N 3200, N 3300, N 3390, N 3400, N 3600, N 3900, Z 4470, HL and IL. Compatibility is generally good with hydroxyfunctional polyesters and polyethers (Desmophen® grades) as well as hydroxy acrylates.
Properties / Applications :
As a particularly low-viscosity polyisocyanate, Desmodur® XP 2860 is particularly well suited for the formulation of high-solids coatings for general industrial coating, automotive refinishing, transportation and plastics coating applications.
Storage :
– Storage in original sealed Covestro container.
– Recommended storage temperature: > 0 – 30 °C.
– Protect from moisture, heat and foreign material.
General information : The product is sensitive to moisture. Storag at higher temperatures will result in increase of color and viscosity.
Storage time :
Covestro represents that, for a period of nine months following the day of shipment as stated in the respective transport documents,the product will meet the specifications or values set forth in section “specifications or characteristic data” above, what ever is applicable, provided that the product is stored in full compliance with the storage conditions set forth in and referenced under section “storage” above and is otherwise handled appropriately. The lapse of the nine months period does not necessarily mean that the product no longer meetsspecifications or the set values. However, prior to using said product, Covestro recommends to test such a product if it still meets the specifications or the set values. Covestro does not make any representation regarding the product after the lapse of the nine months period and Covestro shall not be responsible or liable in any way for the product failing to meet specifications or the set values after the lapse of the nine months period.
Labeling and statutory requirements ：
This product data sheet is only valid in conjunction with the latestedition of the corresponding Safety Data Sheet. Any updating of safety-relevant information – in accordance with statutory requirements – will only be reflected in the Safety Data Sheet, copies of which will be revised and distributed. Information relating to the current classification and labeling, applications and processing methods and further data relevant to safety can be found in the currently valid Safety Data Sheet.
Further information :
The product is used mainly as a hardener in coating materials or adhesives. The handling of coating materials or adhesives containing reactive polyisocyanates and residual monomeric HDI requires appropriate protective measures referred to in the safety data sheet. These products may therefore be used only in industrial or trade applications. They are not suitable for use in homeworker (DIY) applications.
Important :
This is a Trial Product of which we do not yet have extensive experience. No guarantee can therefore be given regarding the behaviour of the product during processing or use.
